Ninja 1000SX

Deco stripe set for 28L panniers. Available in almost all factory standard colours.

Bike cover made from breathable heavy-duty non-woven ripstop material. Kawasaki specific with green honeycomb design elements Easy reach lock buckle. 100% Polyester. With multi usable storage bag.

Developed in conjuction wih SP Connect the kit consists of a Clutch Mount, Anti-vibration module and a Universal Phone Clamp. Suits mosts mobile phones; Simply pull out the crown, screw it tight, and then push the crown back in to lock your phone in place. While remaining fully operable, your phone can now be attached to or detached from the mount in seconds.

Large scratch-resistant smoke windscreen, designed to provide additional rider comfort and styling. Kawasaki branded product, developed by Kawasaki and fully road legal.

For mounting to the Versys 650, the windscreen bracket kit (999941689) is required.

Deco stripe set for 28L panniers. Available in almost all factory standard colours.

Required component of KQR 47 Litre Top Case (99994-0481/99994-0899) (sold separately)

• Includes (1) lock cylinder and all required hardware
• Note: Authorized Kawasaki dealer installation required.
• Ninja 1400GTR owners must reference their vehicle ignition key to determine if a Type A or Type B One Key System is required

Deco stripe set for 28L panniers. Available in almost all factory standard colours.

Cover set for 28L panniers. Available in almost all factory standard colours.

Made from strong Anti-tear Honeycomb ripstop fabric. Heat resistance till 120 degrees Celsius. Subtle branding.
100% Polyester. With multi usable (back)packing string bag.

Charge your portable devices on the go with a 12-volt DC Power Outlet.

• Installs directly into knock-out port on the dash panel
• Dealer installation recommended

Give your Kawasaki Ninja 1000SX a more sporty look with the hexagonal shaped Carbon Akrapovič muffler. This lightweight slip-on is designed to be used together with our pannier system. Consists of a stainless steel inlet, carbon fiber muffler outer sleeve, carbon fiber end cap, Carbon fiber muffler clamp and a Co-branded Akrapovič heat resistant sticker. Carbon fiber heatshield set and fitting kit included. Complies with the applicable European standards.

Help keep your hands warm on the road with a grip heater system ergonomically designed to minimize added bulk to the grip.

• Adjust to low, medium, or high settings with the touch of a button
• Indicator light on the left grip improves setting visibility
• Grip set with all required wiring, brackets and hardware
• Dealer installation recommended

Made from strong Anti-tear Honeycomb ripstop fabric. Heat resistance till 120 degrees Celsius. Subtle branding.
100% Polyester. With multi usable (back)packing string bag.
(XL + top case cover has extra compartment that can be zipped open to make room for top case)

Made from strong Anti-tear Honeycomb ripstop fabric. Heat resistance till 120 degrees Celsius. Subtle branding.
100% Polyester. With multi usable (back)packing string bag.
(XL + top case cover has extra compartment that can be zipped open to make room for top case)

This low seat is slimmer which makes it easier to touch the ground whilst standing still.
For the MY17-MY19 Z1000SX it is 8 mm lower then the original seat.
For the MY20-> Ninja 1000SX it is 28 mm lower then the original seat.

Stylish seat cover to enhance the sporting appearance of the bike. Available in almost all factory standard colours. Replaces the passenger seat of the Ninja 1000SX

Large clear windscreen, designed to provide additional rider comfort.
This screen is approximately 24 mm higher than the standard mounted windscreen.
Kawasaki branded product, developed by Kawasaki and fully road legal.

Genuine Kawasaki chain kit containing engine Sprocket, washer, rear sprocket, nuts and cotter pin etc.
This complete package from Kawasaki contains all the qualified genuine parts required for correct drive chain replacement for popular models.
Compared to aftermarket kits, the genuine kits have the advantage of a rubber coated front sprocket, that will make the chain operation much more quiet. Somebody who has been running an aftermarket kit will know this difference.
The new chain kits have the recognizable green Kawasaki branded packaging.

Standard shape double bubble smoke windshield for wind protection and improved looks. With Kawasaki logo and EU type approval.

Stylish 2-piece set of covers, to accentuate the jagged-edge design of the bike's clutch and alternator.

Solid, easy to install bracket for your navigation system with rubber damping bushes to protect your GPS system from vibrations.
Homologated with motorcycle type approval. Bracket can be adjusted for optimal viewing angle.
Fits most navigation systems.

These protective front axle sliders help to prevent damage to your front axle, front axle nut, fork bottoms, and brake calipers.

USB-A female 5V output for underneath the rear seat to charge your phone or other electric devices.

Give your Kawasaki a more sporty look with the hexagonal shaped Titanium Akrapovič muffler.
This lightweight slip-on is designed to be used together with our pannier system.
Consists of a stainless steel link pipe, stainless steel inlet/ titanium muffler outer sleeve, carbon fiber end cap, Carbon fiber muffler clamp and dual Akrapovič and Ninja 1000SX branded laser etched logo.
Carbon fiber heatshield set and fitting kit included.
Complies with the applicable European standards.

Help protect your motorcycle from tip-over damage.

• High-density black ABS plastic Frame Sliders feature the Kawasaki logo and are mounted with factory-designed metal brackets
• Includes required brackets, hardware and installation instructions
• Frame Sliders help protect your motorcycle but will not prevent all types of damage

Two-piece Gel Seat provides long-distance support and comfort for rider and passenger.

• 15mm increased driver seat heigh over stock
• Gel insert in both sections evens out seating pressure
• Cover construction features low-heat gain material allowing for significantly reduced heat absorption after long periods of sun exposure
• Seat cover features contrasting side material and stitching with Kawasaki logo
• 100% complete for replacement of the stock seat
• Uses factory seat base and components for a factory fit

Pannier fitting kit

Top Case (47L) Bracket for the Ninja 1000SX.
Not compatible with Pannier (2 x 28L) Set.

The Pannier Lock Cylinder set is the key to your user convenience, because by this, you can open your panniers with the same key as you would start your motorcycle.

Large Clear Windscreen

Large windshield, designed to provide additional rider comfort and styling. This screen is approximately 30 mm higher and 60+60mm wider than the standard mounted windscreen. Additionally, it has 80+80mm wider lower area for better wind protection. Kawasaki branded product, developed by Kawasaki and fully road legal.

Top Case (47L) Base Plate

Tank pad to add protection against scratches.

Quick release 56L pannier set that will hold most full-face helmets. Panniers designed to attached to handgrips and footrest and give a clean sporty look when removed. Narrow mounting width of 93cm and suitable for high speed cruising.
Set requires:

• Pannier fitting kit
• Pannier cover set
• Pannier deco stripe set
• Pannier lock cylinder set

Heavy Duty Outdoor Cover - Medium

Strong durable multi layered fabric with taped seams. Heat resistant honeycomb till 120 degrees Celcius. Subtle Branding.
Two front and two rear holes for lock. Covered ventilation openings for better breathing. Window with cover to hide or show license plate.
100% Polyester. With multi usable packing backpack.

Solid, easy to install bracket for your navigation system.
Fits most common current navigation systems.

Made from strong Anti-tear Honeycomb ripstop fabric. Heat resistance till 120 degrees Celcius. Subtle branding. 100% Polyester. With multi usable (back)packing string bag.
Fits:

• Ninja 125
• Ninja 400
• Ninja 650
• Ninja 1000SX (without panniers)
• Ninja H2 SX/SE (without panniers)
• Ninja ZX-4R/RR
• Ninja ZX-6R
• Ninja ZX-10R/RR

For optimal passenger riding comfort. Features a faux leather stitched cover with a quality feel.

Keep your personal items in 47 liters of lockable, waterproof storage; enough room for two full-face helmets. Requires Base Plate and model specific accessories.

• Kawasaki’s One Key System allows you to key the lock to your ignition key – refer to the letter on your key to determine if your need a Type A or Type B system.
• Kawasaki logos and factory-matched trim give your bike a customized look
• Constructed of molded ABS plastic
• Requires Carrier Plate, Color Panel, Deco Plate, and One Key System all sold separately
• Dimensions 432mm (17”) L x 584mm (23”) W x 305mm (12”) H
• Top Case load limit is 5kg (11 lbs.)
• On the Ninja 1000 SX, the Top Case (47L) is not compatible with panniers.

Solid, easy to install genuine bracket for your navigation system.
Fits most common current navigation systems.

Scratch resistant film for your digital dashboard. Will protect the screen against scratches.

Top Case (47L) Aluminium Deco Plates

Stylish wheel rim tape to complete the sporty looks of your bike. (Set of four rings for one bike)

Bike cover made from breathable heavy-duty non-woven ripstop material. Kawasaki specific with green honeycomb design elements Easy reach lock buckle. 100% Polyester. With multi usable storage bag.

Mounting points for paddock stand, providing stability during maintenance or storage. The bobbins are securely attached to the motorcycle's swingarm, allowing for easy and safe lifting of the bike.

Rigid, water-resistant bag with compartments makes it easy to pack your cargo and drop into the locking Top Case. Once you have arrived at your destination, just grab your packed Inner Bag so you can leave the Top Case on your motorcycle and get going.

• Nylon construction with reflective piping
• Purchase as an optional component of the Top Case (42-47L), sold separately

CNC machined billet aluminium Oil Filler Cap with gold finish Note: Compatibility and availability of accessories may vary per specific model year, please check with your Kawasaki Dealer on availability and additional parts needed for installation

Discover your next adventure
Ride challenge level. Plan windy and hilly roads
Discover the world's best curated riding routes, exclusively
Updates via Wi-Fi®. No computer needed
Discover, personalize and enjoy stunning riding routes with MyDrive
Compatible with Siri and Google Now™
Smartphone messages read aloud, hands-free calling
Lifetime* Worldwide Maps, TomTom Traffic and Services
Double the processing speed and five times faster start-up

An essential tool for motorcycle enthusiasts and mechanics alike. Designed to provide stability and convenience, this paddock stand allows easy access to the wheels, suspension, and other components.

This premium rear bike stand can be disassembled, making transportation a lot easier. The compact bike stand comes in a shop worthy carrying case with a built-in carrying handle. The stand is made of premium steel and has a green and black finish. The Kawasaki logo is laser cut in steel.

Optional are the forks to suit your preference;

• The Y-forks are to be used in combination with bobbins. (163JAY0021)
• The L-forks can be used to support the rear swing arms. (163JAY0022)

4-Way super stretch material. Reinforced bottom.

4-Way super stretch material. Reinforced bottom.

Whether you want to park your bike in a pitbox or in your garage, let your precious machine rest in style on this Kawasaki Garage Mat. The mat meets new FIM environmental codes and offers a high level of absorption and dust-control features.

• Size 100cm x 200cm
• Pile weight ± 300 gr/m²,
• Total height ± 5 mm,
• 30°C washable (no tumble-dry)